Select your vehicle

Baja Designs Squadron Pro A-Pillar Light Kit – 447574

Baja Designs

Shop Ford F-150 Offroad Light Packages on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Baja Designs Squadron Pro A-pillar light kit, part number 447574
  • Runs Squadron or S2 series LED lights, driving combo beam
  • 40 watts, 4900 lumens, IP69K waterproof
  • Fitment: 2009–2014 Ford F-150 including SVT Raptor

Description

Overview

The Baja Designs Squadron Pro A-Pillar Light Kit, part number 447574, is a bracket kit that mounts driving lights on the A-pillar of the Ford F-150 and the Raptor. It fits 2009–2014 Ford F-150 trucks, including the SVT Raptor, and runs Squadron or S2 series LED lights.

The kit uses a light pod design with a driving combo beam, rated at 40 watts and 4900 lumens. The housing is designed to hold up to vibration on washboard roads, and installation is simple.

A driving combo beam pairs a focused spot pattern with a wider flood, so the light reaches down the trail while also covering the sides of the path.

It is a direct fit for the 2009–2014 Ford F-150, including the SVT Raptor. The light series is Squadron Pro with a driving combo beam, and installation is straightforward.

Key features

  • A-pillar mounting bracket
  • Compatible with Squadron or S2 series LED lights
  • Driving combo beam pattern
  • 40 watts and 4900 lumens
  • IP69K waterproof, submersible to 9 ft
  • Exceeds MIL-STD810G testing

Mounting and aiming on the A-pillar

A-pillar mounts place lights higher and further forward than bumper mounts, so the beam reaches over the hood and into the trail ahead. Height changes how far the light throws, and it also changes how much glare reflects off dust and rain near the windshield. Aim the pods with the vehicle parked on level ground and a wall or marker ahead, then adjust again after the first few drives because brackets can settle.

Because the pods sit near the cab, the wiring has to be routed cleanly through the pillar trim and away from airbag and wiper components. Use a fused circuit sized for the draw and a relay so the dash switch does not carry the full load. Check the connectors after rough trails, since vibration works loose plugs before it breaks anything else.

  • Re-torque bracket fasteners after the first few trail runs
  • Keep wiring clear of the windshield wiper and airbag area
  • Aim lights again if the bracket has been moved

Specifications

Brand Baja Designs
Part number 447574
Light series Squadron Pro
Type Light pod
Mounting location Bracket, A-pillar
Beam pattern Driving combo
Watts 40
Lumens 4900
Amp draw 2.90
LED life expectancy 49,930 hours
Bulb type LED
Front lens Hard coated polycarbonate
Bezel Billet machined aluminum
Waterproof rating IP69K, submersible to 9 ft
Mil-spec testing Exceeds MIL-STD810G
Overvoltage protection Built in
Sold as Kit

Vehicle fitment

The kit fits the 2009–2014 Ford F-150, including the SVT Raptor, across the standard and special trims covered. Confirm fit for your vehicle’s year, model and trim before ordering if you drive a later F-150 generation or a 2017–2021 Raptor.

Confirm your vehicle’s year, model and trim before ordering.

Installation notes

The 2.90 amp draw suits a small fused circuit, and a relay keeps the switch from carrying the full load. Check local rules on auxiliary lights before using the pods on public roads.

What’s included

The A-pillar bracket kit for the light pods, with Squadron or S2 series lights run from the bracket.

Fitment

VehicleYearsTrims
Ford F-1502009–2014FX2, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lariat Limited, Limited, Platinum, STX, SVT Raptor, XL, XLT

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the 447574 A-pillar kit fit a 2010 Ford F-150?

Yes. It fits the 2009–2014 Ford F-150, including the SVT Raptor. A 2010 model falls within that range, so confirm the trim before ordering.

Which lights work with the Squadron Pro A-pillar kit?

It runs Squadron or S2 series LED lights and uses a driving combo beam pattern. The bracket mounts the light pods on the A-pillar.

Is the 447574 kit rated for water?

Yes. It is rated IP69K, meaning it is waterproof and submersible to 9 ft. It is also built to exceed MIL-STD810G testing.

How should the pods be aimed for trail use compared with highway use?

Aim them slightly lower on trails so the driving combo beam lights the ruts and edges ahead without blinding oncoming drivers. On highways, keep the pods angled down or covered, since the beam reaches out and to the sides at speed. Adjust the aim again after any bracket change.

Do A-pillar light brackets need periodic inspection?

Yes. Check the bracket bolts, the pillar mounting points and the wiring at each service interval and after hard off-road use. Look for loose fasteners, cracked trim, chafed wire and any sign that a pod has shifted. Tightening fasteners and reseating connectors usually restores a secure fit without replacing parts.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Ford F-150 Offroad Light Packages on Amazon