Overview
The Baer Brakes 4262324FR is a Fire Red rear drag race brake kit from the SS4 Plus Deep Stage line, made for Ford 9 inch rear ends with Small Bearing housing ends. It runs two four-piston S4 calipers, each with 1.75 inch pistons, clamping 11.0 inch two-piece rotors on a 5 on 4.50 or 5 on 4.75 bolt circle. It is a smaller package for 15 inch wheels, built for heavy, fast cars that may also see street use.
The axle flange must measure 5.75 inch, so confirm that measurement against your axle before ordering. Brake hoses are not included, while the mounting hardware is. The pads are DR1 (FMSI DR1) with semi-metallic friction material.
Key features
- Two S4 calipers with four pistons each, manufactured in Phoenix, Az
- Two 1.75 inch pistons per caliper with hard anodized aluminum and stainless abutments
- All the benefits of the larger SS4 Plus systems in a package for 15 inch wheels
- Two-piece slotted, drilled, zinc-plated vented rotor
- Billet aluminum hats drilled for 5/8 inch wheel studs
- Powder coated finish and noise suppression clips
- Semi-metallic friction pads, DR1 FMSI number
Drag use and setup
Drag brakes work hardest in short bursts followed by long cooling periods, so the pads and rotors need a steady routine rather than hard stops from the start. Start with several moderate stops to bed the pads, and let the system cool before the next run. Heat management matters as much as stopping power, because overheated pads lose friction and the pedal can go soft.
Hoses and fittings deserve attention on a drag setup. Route new lines away from exhaust heat and moving suspension parts, and secure them so they cannot rub. Check pedal feel before every event, and treat any change in firmness as a reason to inspect the calipers, hoses and fluid.
Keep the rear hardware clean and free of brake dust buildup, since contamination can change friction from run to run.
- Bed in new pads with gradual stops
- Route hoses clear of heat sources
- Check pedal feel before each run
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 4262324FR |
| UPC | 844165038474 |
| Caliper | S4, four-piston, fixed |
| Calipers included | 2 |
| Piston size | 1.75 inch |
| Caliper color | Fire Red |
| Rotor outside diameter | 11.0 inch |
| Rotor thickness | 1.02 inch |
| Rotor construction | Vented, two-piece |
| Rotor surface | Slotted, drilled and zinc plated |
| Hat | Billet aluminum, drilled for 5/8 inch wheel studs |
| Pad FMSI number | DR1 |
| Friction material | Semi-metallic |
| Minimum wheel diameter | 15.0 inch |
| Lug count | 5 lug |
| Bolt pattern | 5×4.50/5×4.75 |
| Axle flange | Ford 9 inch Small Bearing |
| Brake hoses | Not included |
| Park brake | No |
| Sold as | Kit |
| Country of origin | US |
Vehicle fitment
The kit is matched to Ford 9 inch axles with Small Bearing housing ends. Check your housing ends and the 5.75 inch flange before buying, and confirm your vehicle’s year, model and trim before ordering.
Torino (Late Big) bearing housing ends use a different flange and are not covered by this kit. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Drag race use calls for a professional setup. Hoses are not included, so source brake lines that match the calipers and your routing before mounting. Set up the system and bleed it thoroughly, and expect the semi-metallic pads to need a break-in period before full performance.
What’s included
Two S4 calipers with 1.75 inch pistons, two-piece rotors pre-assembled with stainless hardware, mounting hardware and billet aluminum hats drilled for 5/8 inch wheel studs.
Not included: brake hoses, lug nuts, park brake.















