Overview
For Ford 8.8 Inch C-Clip rear ends, the Baer Brakes 4262276B is a black-caliper SS4 rear kit with a 3.25 Inch axle standoff. Its S4 4-piston floating caliper clamps a 12.0 Inch vented, slotted and drilled rotor that is zinc plated. The kit is listed with a 5×4.50 bolt pattern.
The backing plate carries a 1-piece park brake shoe assembly, which makes this a park brake setup, but park brake cables are not included. The hoses are steel braided and DOT approved. The 12 inch SS4 suits most 16 inch or larger wheels and uses DR1 or HB100 pads.
Key features
- Black powder coated S4 calipers
- Machined from forged or billet aluminum
- Dual seals for dust, weather and pressure
- Hard anodized pistons seat against stainless abutments, with noise suppression clips
- 12.0 Inch 1-piece vented rotor, slotted, drilled and zinc plated
- Park brake shoe assembly in the backing plate
- Steel braided hoses with DOT approved brake hose
- Manufactured in Phoenix, Az
Hose and fluid care
Steel braided hoses carry brake pressure without the swelling of rubber lines, but the outer braid can hide corrosion or chafing. Routine inspection means checking the full length for kinks, flat spots and damage near the fittings. Hoses should be replaced as a set if one shows wear, since age affects all of them in the same way.
Brake fluid is the other part that needs regular attention on a setup like this. Fluid absorbs moisture over time, which lowers its boiling point and can make the pedal feel soft under heavy use. Bleeding the system after any hose or caliper work keeps the pedal firm and the response consistent.
- Inspect braided hoses for chafing and kinks
- Replace fluid on a regular schedule
- Bleed the system after any line work
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 4262276B |
| UPC | 844165037996 |
| Caliper | S4, 4-piston |
| Caliper type | Floating |
| Caliper color | Black |
| Rotor outside diameter | 12.0 Inch |
| Rotor thickness | 1.020 Inch |
| Rotor type | 1-piece, vented |
| Rotor material | Iron |
| Surface | Slotted, drilled and zinc plated |
| Wheel bolt pattern | 5×4.50 |
| Minimum wheel diameter | 16.0 Inch |
| Axle flange | Ford 8.8 Inch |
| Axle standoff | 3.25 Inch |
| Hose material | Steel braided, DOT approved |
| Park brake | Yes (shoe assembly included) |
| Park brake cables | Not included |
| ABS tone ring | No |
| Pad type | DR1 or HB100 (FMSI DR1), semi-metallic, performance grade |
| Template | S113E |
| Emission code | 6 |
| Country of origin | US |
Vehicle fitment
Ford 8.8 Inch C-Clip rear ends with a 3.25 Inch standoff are the design this kit covers. Check the standoff against your housing before buying.
Rear ends other than the 8.8 Inch C-Clip design are not covered by this kit. Verify year, model and trim with your vehicle before ordering.
Installation notes
Park brake cables and lug nuts are not included, so plan to have them supplied separately. Steel braided hoses come with the kit. Have a qualified technician install the brakes and bleed the system, and check that the 3.25 Inch standoff matches the housing before fitting.
What’s included
Black S4 4-piston caliper, 12.0 Inch one-piece rotor, backing plate with park brake shoe assembly, and steel braided hoses.
Not included: park brake cables and lug nuts.












