Overview
The Baer Brakes 4302268R is a red Pro Plus 13.0 inch rear disc brake kit for GM 10/12 bolt bearing-on-axle housings with a 5×4.75/5×5.00 wheel bolt pattern. A six-piston fixed caliper clamps a two-piece slotted and drilled rotor, and the backing plate carries a park brake shoe assembly.
The Pro Plus is Performance grade, and its 13 inch rotor suits most wheels 17 inch or larger. The Q110H template verifies clearance. Because wheel styles differ, test the template against the intended wheel before installation.
Key features
- Red six-piston (6P) fixed caliper with stainless steel pistons, abutments and noise suppression clips
- Staggered pistons that help even out pad wear across the pads
- Dual seals keep out dust and weather and hold up under pressure
- Slotted, drilled, zinc-plated two-piece rotor with a billet aluminum hat, pre-assembled with NAS high grade stainless hardware
- Backing plate doubles as the caliper mount and holds a one-piece park brake shoe assembly
- Forged or billet aluminum parts are CNC machined from US sourced stock with a powder coated finish
- Uses D0731 pads; stainless braided hoses and hardware are included
Pad and rotor pairing
Brake pads and rotors are a pair, and worn pads leave the rotor exposed to heat and scoring. When replacing pads, inspect the rotor face for grooves and check the thickness against the value in the service manual before reusing it. Slotted and drilled rotors shed water and gas quickly, but the holes can collect dust and debris, so clean them out during service. Bed the new pads in gradually to transfer an even layer of friction material to the rotor.
Hoses and fittings deserve attention whenever the calipers come off. Braided lines can chafe against suspension parts, so route them away from sharp edges. Check the fittings for seepage after bleeding the system, and tighten them to the specified torque rather than by feel. Use fresh brake fluid of the type the system is built for, and never reuse fluid drained from the lines.
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 4302268R |
| UPC | 844165043225 |
| Sold as | Kit |
| Caliper | 6-piston, fixed, 6P |
| Caliper color | Red |
| Rotor outside diameter (rear) | 13.0 inch |
| Rotor type | 2-piece, slotted, drilled, zinc plated |
| Rotor material | Iron with aluminum hat |
| Rotor construction | Vented |
| Rotor thickness | 1.1 |
| Minimum wheel diameter | 17.0 inch |
| Axle flange | GM small pattern 10/12 bolt bearing on axle |
| Wheel bolt pattern | 5×4.75/5×5.00 |
| Lug count | 5 lug |
| Pad FMSI number | D0731 |
| Hose material | Steel braided, DOT approved |
| Template | Q110H |
| Grade | Performance |
| Country of origin | US |
Vehicle fitment
The application is set by the GM small pattern 10/12 bolt bearing-on-axle flange, used on Buick, Olds and Pontiac rear axles, along with the 5×4.75/5×5.00 bolt pattern. Verify both on your rear axle before committing to this kit.
Installation notes
Park brake cables are not included, so the park brake will need cables from another source. Lug nuts are not included either. Support the vehicle on stands and secure the rear axle before removing the existing brake components.
What’s included
The red kit includes the six-piston caliper assembly, the two-piece rotor with pre-assembled NAS stainless hardware, the backing plate with park brake shoe assembly, and stainless braided hoses with hardware.
Not included: park brake cables, lug nuts and the front rotor.















