Overview
The Baer Brakes 4261079B is a black Extreme Plus front brake kit made for a set of 1970 to 1974 Ford and Mercury cars that came with drum brake spindles. Coverage is 1970 Ford Fairlane and Falcon, 1970 through 1974 Ford Maverick, 1970 through 1973 Ford Mustang, 1970 through 1971 Ford Torino, 1971 through 1974 Mercury Comet, 1970 through 1973 Mercury Cougar, 1970 Mercury Cyclone and 1970 through 1971 Mercury Montego.
Each kit uses a 6S monoblock six-piston caliper in black on a 14.0 inch two-piece rotor. Billet aluminum hubs carry premium bearings packed in Redline synthetic grease and are finished with billet dust caps. Baer adds that wheel fit cannot be guaranteed across all wheel makers, so check the N085P template against the wheel.
Key features
- Six-piston monoblock 6S caliper finished in black powder coat
- Stainless pistons, stainless abutments and noise suppression clips
- Staggered pistons and dual dust, weather and pressure seals
- Two-piece slotted, drilled, zinc-plated rotor on a billet aluminum hat
- Rotor hardware pre-assembled with NAS high grade stainless
- Billet hubs with premium bearings and billet dust caps
- Stainless braided hoses and mounting brackets included
Wheel fit and stud checks
Wheel fit on this type of kit depends on more than the rotor size. Stud length, the lug seat style and the wheel’s center bore all decide whether the wheel mounts flat and clears the caliper. A template check against the wheel you intend to run is the most direct way to confirm clearance before mounting tires.
Billet hubs with bearings already packed are a convenience, but the hub surface and the rotor hat still need a clean mounting face. Remove any rust, paint or debris from the hub and rotor contact areas, and make sure the rotor sits without wobble before the wheel goes on. Runout at the hub is often the cause of pulsation under braking.
Brake pads and rotors wear over time, so periodic checks belong in routine maintenance. Look at pad thickness through the caliper window, check the rotor for scoring or heat cracks, and listen for squealing or grinding. Keep the caliper pins and slide surfaces lubricated with appropriate grease whenever the wheels come off for service.
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 4261079B |
| UPC | 844165035589 |
| Caliper | 6S, 1-piece monoblock, 6-piston, fixed |
| Caliper color | Black |
| Rotor outside diameter | 14.0 inch |
| Rotor thickness | 1.25 |
| Rotor construction | 2-piece, vented |
| Rotor surface | Slotted, drilled and zinc plated |
| Rotor material | Iron with aluminum hat |
| Hub | Billet aluminum |
| Bearings | Premium, packed with Redline synthetic grease |
| Dust caps | Billet |
| Hoses | Stainless steel braided |
| Pad type | FMSI D1247 |
| Template | N085P |
| Wheel bolt pattern | 5×4.50 |
| Lug count | 5 |
| Wheel stud size | 1/2-20 x 2.25 Inch |
| Minimum wheel diameter | 18.0 inch |
| Axle | Front |
| Grade | Performance |
| Front rotor included | Yes |
| Lug nuts included | No |
| Country of origin | US |
Vehicle fitment
Vehicles that use factory disc brake spindles are not covered by the listed fitment. Years outside the listed ranges are not included.
Check the model year and spindle type against the list above. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Billet hubs arrive with bearings already assembled and packed, and brackets and braided hoses come in the kit. Lug nuts are sold separately. Verify the 1/2-20 x 2.25 inch stud fit and the 5×4.50 pattern against your wheels, and have a qualified mechanic confirm spindle clearance before driving.
What’s included
Front rotor with billet hub, 6S black caliper, stainless braided hoses, brackets and pre-assembled hardware.
Not included: Lug nuts.














