Overview
The Baer Brakes 05365-020 is a set of front Claw performance brake rotors for the 1994–1999 Dodge Ram 1500 with 4WD. Baer Brakes describes them as direct replacement rotors, so they mount in place of the factory front discs.
The cross-drilled and slotted face lets gases and dust leave the gap between pad and rotor during braking, which supports a steadier pedal feel and less brake fade. The rotors are zinc-plated, giving a bright look behind open-center wheels.
Key features
- Slotted and cross-drilled friction face carries gases and dust away from the pad.
- Enhanced vane structure, which Baer Brakes describes as improving cooling and durability.
- Premium, mill balanced direct replacement rotor.
- Chamfered cross-drilled holes, meant to reduce stress cracking.
- Zinc-plated finish with a rust resistant coating.
Before you buy
Brake rotors wear with every stop, and the friction face shows it first. Before buying a replacement set, look at how the truck is driven and where it is used. Highway driving with light loads puts less heat into the rotors than towing or steep grades, and that affects how quickly pads and rotors wear. Pads should be matched to the rotor material and to your driving, since a mismatch can cause noise, uneven wear or weak bite when cold.
Cross-drilled and slotted rotors are often chosen for their look and for how they handle gas and dust, but the extra edges can crack under heavy heat. Inspect the drilled holes and slots at each brake service. Small hairline cracks near the holes are a reason to replace the rotor rather than keep it in service.
- Replace front rotors in pairs so braking stays even
- Bed in new pads with several moderate stops
- Clean hub faces and remove rust before mounting
- Check wheel bearings and caliper slides at the same time
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 05365-020 |
| UPC | 844165000624 |
| Supplied as | Set of two rotors |
| Rotor construction | 1-piece, full cast |
| Axle | Front |
| Drive | 4WD |
| Rotor type | Vented, conventional |
| Brake surface | Directional |
| Surface type | Slotted and cross-drilled |
| Material | Cast iron |
| Finish | Zinc-plated, rust resistant coating |
| Grade | Premium |
| Outside diameter | 294.9 mm (11.61 in) |
| Nominal thickness | 32.7 mm (1.29 in) |
| Discard thickness | 30.86 mm (1.21 in) |
| Overall height | 65.6 mm (2.58 in) |
| Center hole diameter | 78.6 mm (3.09 in) |
| Stud/lug hole quantity | 5 |
| Stud/lug hole circle diameter | 139.7 mm (5.5 in) |
| ABS tone ring included | No |
| Emission code | 6 |
| Country of origin | CN |
Vehicle fitment
This set fits the 1994–1999 Dodge Ram 1500 with 4WD on the front axle. Ram 2500 and Ram 3500 models and Ram years outside 1994–1999 are outside this fit. Confirm fit for your vehicle’s year, model and trim before ordering.
The fitment does not cover Ram 2500 or Ram 3500 models or any Ram years outside 1994–1999. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Install both front rotors together so the pair matches. Check each rotor against the 30.86 mm (1.21 in) discard thickness before reinstalling it, and replace any rotor at or below that figure. The ABS tone ring is not part of this kit.
What’s included
A pair of front direct replacement rotors with a cross-drilled and slotted surface, a zinc-plated finish and one-piece full cast construction.
Not included: ABS tone ring.
