Overview
The Aries TrailCrusher Front Bumper, part 2156002, is a one-piece steel bumper for the 2018–2026 Jeep Wrangler JL and the 2020–2026 Jeep Gladiator JT. Aries built it to be used on the trail with a winch and shackles, and it mounts high and tight to the front of the Jeep for ground clearance over rocky terrain.
The bumper is made from 3/16 inch thick steel plate welded into one piece. It has 1/4 inch thick shoulder sleeves and 3/8 inch thick steel brackets. Aries says its testing gives the bumper a winch rating and a shackle rating of 12,500 lb straight-line pull.
The center section has pre-drilled, slotted holes that form a universal winch mount. It accepts most aftermarket winches without extra brackets, although the winch is not included. The front has pre-drilled holes for a hawse fairlead, #2156070, or a roller fairlead, #2156071.
The shackle mounts are welded to the 1/4 inch shoulder sleeves and take a 7/8 inch diameter pin. ARIES shackles #2166071 are rated for 12,500 lb straight-line pull and fit those mounts.
A stinger-style brush guard, #2156050, made from 3/16 inch steel, bolts onto the shoulder sleeves to protect the winch from brush and rocks. It gives the bumper an aggressive look. The brush guard is not included with the bumper.
The bumper is finished with an E-coat and a carbide black powder coat, which Aries says resists rust, chips and UV. A rear bumper, #2157002, is also available.
Key features
- One-piece steel construction with 3/16 inch plate
- Winch and shackle rating of 12,500 lb straight-line pull
- Pre-drilled, slotted universal winch mount
- Pre-drilled holes for hawse or roller fairleads
- Welded shackle mounts for a 7/8 inch diameter pin
- Stinger brush guard option, #2156050
- Narrowed stubby width that works with large offroad tires
- Light mounts and D-ring mount included
Winch recovery basics
A front bumper with a winch mount changes how recovery work is done, so plan the setup before the vehicle is stuck. Keep the winch line straight and avoid pulling at an angle across the bumper, since side loads stress the mounts and the shackle points. Use rated shackles and soft recovery straps where they suit the job, and keep bystanders clear of the line during every pull.
Inspect the winch mount, shackle pins and fairleads before each trip. Look for bent parts, cracked welds, worn pin holes and loose bolts, and tighten or replace anything that shows wear. Store the winch and cable out of direct sun when the truck is parked, since heat and grit wear the cable faster.
- Keep the line straight during pulls
- Inspect the shackle pins before each trip
- Keep bystanders clear of the line
Specifications
| Brand | Aries Offroad |
|---|---|
| Part number | 2156002 |
| Position | Front |
| Width | Stubby |
| Material | Steel, 3/16 inch plate |
| Shoulder sleeves | 1/4 inch thick steel |
| Brackets | 3/8 inch thick steel |
| Winch rating | 12,500 lb straight-line pull |
| Shackle rating | 12,500 lb straight-line pull (ARIES shackle #2166071) |
| Shackle pin | 7/8 inch diameter |
| Finish | E-coat and carbide black powder coat |
| Light mounts | Included |
| D-ring mount | Included |
Vehicle fitment
The bumper fits the 2020–2026 Jeep Gladiator and the 2018–2026 Jeep Wrangler JL.
Wrangler JK models and Gladiator model years before 2020 are not on the list. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
The bumper uses the factory mounting points, so no drilling is required. Installation also needs no pump relocation, and the 3/8 inch brackets come with all the hardware for a complete installation.
What’s included
All necessary installation hardware, the D-ring mount and the light mounts. Not included: the winch, the stinger brush guard #2156050, and the ARIES shackles #2166071. The fairleads #2156070 and #2156071 are separate parts.











