Select your vehicle

Rock Hard 4X4 Parts Rear Angle Bars – RH1001-A

Rock Hard 4x4 Parts

Shop Jeep Wrangler TJ Roll Cage on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Rock Hard 4×4 Parts rear angle bars, part number RH-1001-A
  • Bolt-in, 1-3/4 inch x.120 wall tubing in unpainted bare steel
  • Fits 1997-2002 Jeep Wrangler TJ SE, Sahara, Sport and X
  • Without a front sport cage, RH1001-G clamps and end caps are needed

Description

Overview

The Rock Hard 4×4 Parts RH-1001-A is a set of rear angle bars for the Rock Hard 4×4 sport cage. The bars use 1-3/4 inch x.120 wall tubing and come unpainted in bare steel.

The manufacturer fitment list places the rear angle bars on the 1997-2002 Jeep Wrangler (TJ) in SE, Sahara, Sport and X trims. Without a front sport cage, RH1001-G clamps and end caps are required for installation.

Key features

  • Bolt-in installation type
  • 1-3/4 inch x.120 wall tubing
  • Unpainted bare steel finish
  • Made in the U.S.A.
  • It is a direct fit for the 1997-2002 Jeep Wrangler TJ.
  • Requires RH1001-G clamps and end caps when the front sport cage is absent

Before you install

Rear angle bars brace the back of a sport cage, helping it resist side-to-side movement when the Jeep flexes on uneven trail. Because they bolt in rather than being welded, the fit depends on the cage and mounting points lining up cleanly with the rear of the frame. Take the time to test-fit the bars and check that all fasteners draw down evenly before the first trip.

Bare steel is a practical finish for a part that will be used off-road, but it will rust over time if the bars sit in wet mud or road salt. Wipe off dirt after trail runs, look for surface rust at the joints, and touch up any bare spots with a suitable paint or coating. Periodic checks of the bolts are worth making, since vibration on the trail can loosen fasteners that were correct at installation.

If the front sport cage is not in place, the clamps and end caps become essential, and they should be inspected alongside the bars. Look for cracked welds, bent tubing or elongated bolt holes after a hard hit, and replace any damaged piece rather than trying to repair it on the trail.

  • Test-fit the bars before final tightening
  • Inspect joints for surface rust after wet runs
  • Recheck bolts after the first few trips

Specifications

Brand Rock Hard 4×4 Parts
Part number RH-1001-A
UPC 70000364018
Tubing 1-3/4 inch x.120 wall
Finish Unpainted bare steel
Installation type Bolt in
Origin Made in the U.S.A.

Vehicle fitment

The manufacturer fitment list covers the 1997-2002 Jeep Wrangler (TJ) in SE, Sahara, Sport and X trims.

Models outside the 1997-2002 TJ range are not on this list. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

The installation is bolt-in. Without the front sport cage, RH1001-G clamps and end caps are needed, so have them on hand before fitting the angle bars.

What’s included

Rear angle bars in unpainted bare steel.

Not included: the front sport cage and the RH1001-G clamps and end caps, which are needed when the front sport cage is absent.

SKU: RFPRH-1001-A Category:

Specification

Shipping weight 14.45 lbs
Package dimensions 52.30 × 5.50 × 3.50 in
brands

Fitment

VehicleYearsTrims
Jeep Wrangler (TJ)1997–2002SE, Sahara, Sport, X

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

What is the Rock Hard 4x4 Parts RH-1001-A?

It is a set of rear angle bars for the Rock Hard 4x4 sport cage, part number RH-1001-A, with 1-3/4 inch x.120 wall tubing in unpainted bare steel. The installation is bolt-in and the bars are made in the U.S.A.

Does the RH-1001-A fit a Jeep Wrangler TJ?

Yes. The manufacturer fitment list covers the 1997-2002 Jeep Wrangler TJ in SE, Sahara, Sport and X trims. Confirm your year and trim before choosing these bars for your vehicle.

What else do I need to install these bars?

Only if the front sport cage is missing. Without it, RH1001-G clamps and end caps are needed. The installation is bolt-in, so confirm you have all required parts before starting.

Should I paint the angle bars?

Painting is optional, but it helps slow rust on bare steel. Clean the surface, remove any mill scale or grease, and use a paint suited to steel before applying. Recheck the coating after trail use, and touch up chips early so corrosion does not spread under the finish.

Do the angle bars need regular checks?

Yes. Tighten the bolts after the first few trips, then inspect them periodically. Look for loose fasteners, cracks near the welds and any movement at the mounts. Address problems before the next outing, since a loose bar can shift under load.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Jeep Wrangler TJ Roll Cage on Amazon