Select your vehicle

Mountain Off Road Enterprises Shackle Reverse System – 7686-2

Mountain Off Road Enterprises

Shop Jeep CJ7 Shackle Reversal Kits on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Mountain Off Road Enterprises 7686-2 Shackle Reverse System (S.R.S.) for front suspension
  • Fits 1976–1983 Jeep CJ5 and 1976–1986 Jeep CJ7
  • Brackets and hardware included; longer front drive shaft slip-yoke required

Description

Overview

The Mountain Off Road Enterprises Shackle Reverse System 7686-2, also called an S.R.S., is a front suspension kit for the 1976–1983 Jeep CJ5 and the 1976–1986 Jeep CJ7. It reverses the front pivot point so the leaf spring and shackle absorb more of an obstacle impact.

The stock design transmits part of a front tire strike back to the frame through a solid rear pivot point. Reversing the pivot lets the spring and shackle absorb that impact, for a more even suspension response over obstacles. The kit includes brackets and hardware.

Key features

  • Reversed front pivot point so the spring and shackle absorb more of each impact
  • New front pivot brackets that move the front axle forward from the stock position
  • Forward axle position means the tire is less likely to contact the fender as the spring compresses
  • Maker reports a smoother ride, less wandering and less darting at higher speeds
  • Brackets and hardware included
  • Powdercoated black finish

Choosing a reversed pivot setup

A reversed front pivot changes where the leaf spring is anchored, so the spring flex, the axle position and the drive shaft length all change together. Many owners find that the front driveline needs attention as part of the same job, and the alignment should be checked once the system is in. Plan the installation so that the drive shaft work is scheduled before the vehicle is returned to the trail.

Front pivot kits interact with the steering and brake lines, so route the lines after the brackets are set and check for clearance at full suspension compression. Inspect the spring hangers and axle mounts for wear while the system is off, since they carry the altered load.

  • Schedule drive shaft work before installation
  • Check brake and steering line clearance
  • Confirm alignment after the system is fitted
  • Inspect spring hangers and axle mounts for wear

Specifications

Brand Mountain Off Road Enterprises
Part number 7686-2
UPC 815572022684
Application Front suspension, leaf spring pivot
Finish Powdercoated black
Included Brackets and hardware
Pitman arm Keep stock, no drop
Front drive shaft Longer travel slip-yoke required

Vehicle fitment

This kit fits the following Jeep models:

  • 1976–1983 Jeep CJ5 (Base, Golden Eagle, Laredo, Limited, Renegade)
  • 1976–1986 Jeep CJ7 (Base, Golden Eagle, Golden Hawk, Laredo, Limited, Renegade)

Wrangler YJ, TJ and LJ models and the Jeep Scrambler are not covered. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

The longer travel slip-yoke must be installed by a professional drive shaft builder, because the reversed pivot needs more front drive shaft travel than stock. Keep the stock pitman arm with no drop. Once the system is fitted, have the front alignment checked and keep the axle and spring hardware properly supported during work.

What’s included

Brackets and hardware for the system are included.

Not included: A longer travel slip-yoke for the front drive shaft, which must be installed by a professional drive shaft builder.

SKU: MRE7686-2 Category:

Specification

Shipping weight 26.72 lbs
Package dimensions 42.00 × 9.00 × 5.00 in
brands

Fitment

VehicleYearsTrims
Jeep CJ51976–1983Base, Golden Eagle, Laredo, Limited, Renegade
Jeep CJ71976–1986Base, Golden Eagle, Golden Hawk, Laredo, Limited, Renegade

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the Mountain Off Road 7686-2 fit a Jeep CJ7?

Yes. It fits the 1976–1986 Jeep CJ7 in Base, Golden Eagle, Golden Hawk, Laredo, Limited and Renegade trims. Confirm your vehicle's year, model and trim before ordering.

Does this kit require a different drive shaft?

Yes. The reversed pivot requires a longer travel slip-yoke in the front drive shaft, which should be installed by a professional drive shaft builder because the shaft needs more travel than stock.

Is a pitman arm change needed?

No drop pitman arm is required. The stock pitman arm is kept, with no drop, when the system is installed.

Do reversed pivot kits need regular inspection?

Yes. Check the brackets, bolts and spring mounts for looseness after the first few trail runs, and inspect the drive shaft angles at regular service intervals.

Can a shackle reverse system be combined with other front suspension work?

Often it is paired with new bushings or spring work. Confirm that the drive shaft length and steering geometry still suit the combined setup before driving the vehicle.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Jeep CJ7 Shackle Reversal Kits on Amazon