Overview
The Bilstein 5125 Series Shock Absorber, part number 33-104652, is a rear gas charged shock for custom lifted applications. It fits 1969 to 1974 and 1977 to 1986 Chevrolet K30 pickups, the 1970 GMC C35 and C3500, the 1977 to 1978 GMC K35, the 1969 to 1974 GMC K35 and K3500, and the 1979 to 1986 GMC K3500.
The 5125 Series uses a single tube high gas pressure design for consistent, fade free performance and long life. Its lift range is w/2 – 2.5 in. Lift, with a 14mm shaft diameter and 5/8 inch eye mounts at both ends.
Bilstein offers the 5125 Series by travel length for custom applications. This unit has a travel length of 10.99 in, a collapsed length of 17.01 in and an extended length of 28 in.
Key features
- Mono tube gas pressure construction
- Self-adjusting deflecting disc valving
- High-flow piston that reduces harshness
- Independent rebound and compression tuning
- Larger working piston area for exact damping
- Superior control with large diameter tires
Sleeves and mounting
Rear shocks on older trucks often sit on mounts that have worn or been replaced with aftermarket parts, so the sleeve size matters. Measure the inside diameter of each eye before choosing sleeves, then test-fit the shock by hand. A proper fit keeps the bushing centered and stops the eye from moving under load.
A rear shock on a lifted truck works hard when the axle moves through its travel. Check the upper and lower brackets for cracks and loose welds. Replace bushings that show tearing or flattening, and tighten fasteners once the truck is back on the ground so the rubber is not pre-loaded.
- Test-fit each sleeve before tightening
- Inspect rubber bushings for tearing
- Check bracket welds on the axle and frame
- Tighten fasteners with the truck at ride height
Specifications
| Brand | Bilstein |
|---|---|
| Part number | 33-104652 |
| UPC | 651860591384 |
| Shock series | 5125 Series |
| Position | Rear |
| Fitment type | Direct fit |
| Lift height | w/2 – 2.5 in. Lift |
| Hydraulic / gas charged | Gas charged |
| Collapsed length | 17.01 in |
| Extended length | 28 in |
| Travel length | 10.99 in |
| Compression | 700 |
| Rebound | 2550 |
| Lower mount | 5/8 inch eye |
| Upper mount | 5/8 inch eye |
| Shaft diameter | 14mm |
| Reservoir | No |
| Finish | Zinc plated |
| Body design | 46mm ID smooth body (non-coilover) |
| Internal design | Mono tube |
| Boot included | Yes |
| Mounting parts included | 1/2 inch sleeves and a 12mm sleeve |
Vehicle fitment
It fits the 1969 to 1974 and 1977 to 1986 Chevrolet K30, in trims including Cheyenne, Custom, Custom Deluxe, Deluxe, Pickup Base, Scottsdale and Silverado. It also fits the 1970 GMC C35 and C3500 (Pickup Base), the 1977 to 1978 GMC K35, the 1969 to 1974 GMC K35 and K3500 (Pickup Base), and the 1979 to 1986 GMC K3500.
Years between the two listed ranges for the Chevrolet K30 are not on this list. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
The package includes 1/2 inch and 12mm sleeves for the 5/8 inch eye mounts. Confirm which sleeve fits your mount before installing.
What’s included
One rear 5125 Series shock absorber with a boot, plus 1/2 inch sleeves and a 12mm sleeve.









