Overview
The Baer Brakes 4262322C is a clear-caliper rear drag brake kit for Ford 9 inch early big bearing housing ends, using 5×4.5 and 5×4.75 bolt pattern wheels. It is part of Baer’s SS4 Plus Deep Stage group and suits heavy, fast cars that may also be driven on the street.
Each side runs an S4 caliper with four pistons, squeezing an 11.0 inch two-piece slotted, drilled rotor. The pads are high friction units made for drag racing and come with the kit as standard equipment. The system suits wheels 15 inches and larger and requires a 5.75 inch axle flange.
Key features
- High friction drag race pads come standard with the kit
- S4 calipers in a clear finish with four pistons each
- 1.75 inch pistons in hard anodized aluminum
- Two-piece zinc-plated rotors with aluminum hats
- Stainless abutments and noise suppression clips
- Wheel stud holes at 5/8 inch in billet aluminum hats
Housing and flange check
Axle housing and flange type decide whether a drag kit bolts up at all, so start there before looking at calipers or rotors. Early big bearing ends and later flange designs look similar but are not interchangeable, so compare the housing casting and flange shape against your axle. Measure the flange before ordering and keep old hardware out of the new install.
High friction drag pads are aggressive compounds. They need a careful bedding routine before hard use, and they can transfer material to the rotor if they overheat or cool too quickly. Once the kit is on, check pad thickness and rotor surface after the first few sessions. Glazing, cracking or a pulsing pedal are signs that the pads or rotors are worn or overheated and need attention.
- Compare the housing casting with your axle before ordering
- Keep pads and rotors matched as a set
- Check caliper clearance with the wheel installed
- Use fresh brake fluid suited to high temperature use
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 4262322C |
| UPC | 844165038443 |
| Supplied as | Kit |
| Axle position | Rear |
| Axle flange | Ford 9 inch early big bearing |
| Bearing type | Big Bearing |
| Axle flange size required | 5.75 inch |
| Caliper | S4, two-piece, four-piston, fixed |
| Calipers included | 2 |
| Caliper finish | Clear |
| Piston size | 1.75 inch |
| Rotor outside diameter | 11.0 inch |
| Rotor thickness | 1.02 inch |
| Rotor type | Two-piece, vented, slotted, drilled, zinc-plated |
| Rotor material | Iron with aluminum hat |
| Pad type | DR1 or HB100 (FMSI DR1) |
| Friction material | Semi-metallic |
| Grade | Performance |
| Wheel bolt pattern | 5×4.50/5×4.75 |
| Lug count | 5 |
| Minimum wheel diameter | 15.0 inch |
| Park brake | No |
| Emission code | 6 |
| Country of origin | US |
Vehicle fitment
This is an axle-housing kit for Ford 9 inch early big bearing ends. Confirm fit for your vehicle’s year, model and trim before ordering. Check the housing and the 5.75 inch flange against your axle before ordering.
Torino/late big bearing housings use a separate flange type in this family, so do not mix them up. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Mounting hardware and the stainless rotor hardware come with the kit, so the swap centers on fitting the housing ends and checking caliper-to-rotor clearance. Lug nuts and brake hoses must be added separately. High friction drag pads generally need careful bedding-in before hard use, and a qualified installer should bleed the hydraulics once the lines are connected.
What’s included
Two clear S4 calipers, two-piece rotors with aluminum hats, the high friction drag pads and the mounting hardware.
Not included: Lug nuts and front rotors are needed separately, and brake hoses fall outside the kit.















