Overview
The Baer Brakes 4262684FR is a deep stage dual rear brake kit for Ford 8.8 inch rear ends fitted with C-clip eliminators and a 2.5 inch axle standoff. It places four S4 calipers in Fire Red over 11 inch two-piece slotted, drilled rotors, for drag racing and heavy, fast cars that may also see street use.
The SS4 Plus Dual Deep Stage was developed as a smaller-package drag system that still uses the benefits of Baer’s larger brake systems. Rotors fit wheels 15 inch and larger, and the kit uses the DR1 or HB100 pad type with high friction pads for drag race work. It is manufactured in Phoenix, Az.
Key features
- Four S4 calipers with 4-piston design and 1.375 inch pistons
- Hard anodized aluminum pistons with stainless steel abutments
- Two-piece zinc plated rotors, slotted and drilled, with iron rotor and aluminum hat
- Billet aluminum hats drilled for 5/8 inch wheel studs
- Rotors pre-assembled with stainless hardware
- Powder coated Fire Red calipers
Standoff and clearance checks
A standoff moves the caliper and rotor position relative to the axle housing, so the spacing affects clearance to the wheel, the tire and any suspension component nearby. Before final assembly, set the rotor and caliper positions and check that nothing touches through a full range of suspension travel. Ford 8.8 housings with C-clip eliminators often need wheel bearing and hub inspection at the same time.
Because the rotors are pre-assembled, the hub face and flange should be cleaned of old residue and checked for flatness before bolting on. Rotor runout on a worn hub can cause pedal pulsation. Torque the hardware in a star pattern and recheck it after the first few runs.
- Verify caliper clearance to the wheel at full steering lock
- Inspect the axle bearing and seal before installing
- Confirm the standoff thickness matches the housing before assembly
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 4262684FR |
| UPC | 844165049074 |
| Sold as | Kit |
| Caliper | S4, 4-piston, fixed, Fire Red |
| Piston size | 1.375 inch |
| Rotor outside diameter | 11.0 inch |
| Rotor thickness | 1.02 |
| Rotor type | 2-piece, vented, slotted and drilled, zinc plated |
| Rotor material | Iron with aluminum hat |
| Pad type | DR1 or HB100, semi-metallic friction material |
| Axle flange | Ford 8.8 inch, C-clip eliminator housing |
| Axle standoff | 2.5 inch |
| Axle flange dimension | 5.75 inch |
| Wheel bolt pattern | 5×4.50/5×4.75 |
| Lug count | 5 lug |
| Minimum wheel diameter | 15.0 inch |
| Template | S125A |
| Emission code | 6 |
| Park brake | No |
Vehicle fitment
It is built for Ford 8.8 inch rear ends with C-clip eliminators, so the housing and its 5.75 inch axle flange decide whether it bolts up. Confirm fit for your vehicle’s year, model and trim before ordering.
Ford small bearing housing ends and GM small pattern housings are different designs and are not covered by this kit. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Measure the axle flange before starting, since this kit requires 5.75 inch. The 2.5 inch axle standoff is part of the setup, so confirm it suits your housing before assembly. Mounting hardware is included with the pre-assembled rotors. Brake hoses are not supplied, so arrange them separately.
What’s included
The kit includes four S4 calipers with 1.375 inch pistons, pre-assembled two-piece rotors with stainless hardware, DR1 or HB100 pads, and mounting hardware for the dual rear setup.
Not included: brake hoses, park brake hardware, front rotor and lug nuts.















