Overview
Baer’s SS4 Plus 11.0 inch rear brake kit in red, part number 4262690R, targets rear axles fitted with Ford 8 inch or 9 inch small bearing housing ends and a 5×4.5 or 5×4.75 bolt circle. Fitment entries show 1965–1973 Ford Mustang, covering Boss, Grande, Mach 1 and Shelby GT-350 and GT-500 models.
A 4-piston S4 fixed caliper clamps an 11 inch 2-piece rotor, which is slotted, drilled and zinc plated with a billet aluminum hat. Steel braided hoses and mounting brackets come in the kit, and the rotor arrives pre-assembled with stainless hardware. A park brake is not part of the package.
Key features
- Red-finished S4 caliper with powder coated surface
- Hard anodized aluminum pistons with stainless steel abutments
- Noise suppression clips included with the caliper hardware
- Dual seals for dust, weather and pressure
- CNC machined from forged or billet aluminum
- 2-piece zinc-plated rotor with billet aluminum hat
- Steel braided hoses with DOT approval
Before you buy
Red calipers are a finish choice, so the performance and fit come from the caliper design, rotor size and axle match. Start with the housing type, then the bolt circle, then the flange diameter, since a mismatch at any of these stops the install before the brakes are tested.
Rear brakes should be inspected at each tire rotation, checking pad thickness, rotor scoring and hose condition. Replace pads in pairs on the same axle and bed them in with a few moderate stops before loading the vehicle. Keep brake fluid fresh, since moisture lowers its boiling point over time and softens pedal feel. Lug nut torque and hub cleanliness are worth checking after the first few trail runs or the first week of street driving.
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 4262690R |
| UPC | 844165047995 |
| Sold as | Kit |
| Axle | Rear |
| Lug count | 5 lug |
| Wheel bolt pattern | 5×4.50/5×4.75 |
| Axle flange | Ford 8 inch/9 inch small bearing |
| Required axle flange diameter | 5.75 inch |
| Caliper | S4, 4-piston |
| Caliper type | Fixed |
| Caliper color | Red |
| Rotor outside diameter | 11.0 inch |
| Rotor thickness | 1.020 inch |
| Rotor type | 2-piece |
| Rotor construction | Vented |
| Rotor material | Iron with aluminum hat |
| Rotor surface | Slotted, drilled, zinc plated |
| Minimum wheel diameter | 15.0 inch |
| Pad FMSI number | DR1-C |
| Template | S125A |
| Hose material | Steel braided |
| Brake hose DOT approved | Yes |
| Park brake included | No |
| Grade | Performance |
| Country of origin | US |
Vehicle fitment
Fitment data names the 1965–1973 Ford Mustang with its Boss, Grande, Mach 1 and Shelby variants, and no other vehicles.
Vehicles outside that Mustang range and non-Mustang Ford models are not covered. Check the 5.75 inch axle flange requirement against your housing before choosing this kit. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Small bearing housings are the match here, and big bearing housing ends are a different fit. Brackets and braided hoses come in the kit, so no line fabrication is needed. Test the brakes at low speed after installation, since rear brake work changes stopping behavior.
What’s included
The kit contains the S4 red caliper, mounting brackets, steel braided hoses, the 11.0 inch rotor pre-assembled with stainless hardware, and hardware.
Not included: lug nuts and a park brake.















