Overview
The Baer Brakes Pro Plus 4262181R is a red rear brake kit for Ford 8 Inch/9 Inch small bearing rear axle housing ends with a 5×5.00 inch bolt pattern. It combines a six-piston fixed caliper with a two-piece 14.0 inch slotted, drilled and zinc-plated rotor. The 14 inch Pro Plus fits most wheels 18 inches or larger.
The backing plate doubles as the caliper mount and holds a one-piece park brake shoe assembly. The pad type is D0731, and the Q082P template is used to check wheel clearance. The caliper is made in Phoenix, Az.
Key features
- Red six-piston (6P) fixed rear caliper with powder-coated finish
- Two-piece 14.0 inch slotted, drilled and zinc-plated rotor with billet aluminum hat
- Stainless steel pistons, abutments and noise suppression clips
- Staggered pistons to help limit uneven pad wear
- Dual seals for dust, weather and pressure
- Park brake shoe assembly housed in the backing plate
- Steel braided hoses with stainless hardware, DOT approved
Checking the rear brake system
A rear brake kit works with the axle, the rotor and the caliper as one system. When the pedal is pressed, the caliper pistons squeeze the pads against the spinning rotor, and the park brake shoe inside the backing plate holds the vehicle when parked. Because the rotor, caliper and backing plate share the same hub and mounting points, fitting one part without checking the others can leave clearance or alignment problems.
Before ordering, confirm the axle flange and bolt pattern, then plan on replacing the pads and hoses when the rest of the system is opened. Rotor wear shows up as a lip at the outer edge, pulsation through the pedal, or squeal from the pads. Keep brake fluid clean, and bleed the lines after any hose change so the pedal stays firm.
- Check the axle flange and bolt pattern before buying
- Replace pads, hoses and hardware together when the system is opened
- Inspect the park brake shoe for wear during service
- Use fresh brake fluid after any line work
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 4262181R |
| UPC | 844165036920 |
| Sold as | Kit |
| Caliper | Six-piston (6P) fixed, red |
| Rotor outside diameter | 14.0 inch |
| Rotor thickness | 1.15 |
| Rotor type | Two-piece, vented |
| Rotor material | Iron with aluminum hat |
| Surface | Slotted, drilled and zinc plated |
| Wheel bolt pattern | 5×5.00 inch, 5 lug |
| Minimum wheel diameter | 18.0 inch |
| Axle flange | Ford 8 Inch/9 Inch small bearing |
| Brake pad FMSI number | D0731 |
| Hose material | Steel braided, DOT approved |
| Template | Q082P |
| Park brake | Included in backing plate (one-piece shoe assembly) |
| Country of origin | US |
Vehicle fitment
Fitment is set by the Ford 8 Inch/9 Inch small bearing axle flange and the 5×5.00 inch bolt pattern, so the axle housing ends are the deciding match. Confirm fit for your vehicle’s year, model and trim before ordering.
Check the flange name on your axle against the small bearing description before anything else. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Park brake cables, lug nuts and the front rotor are excluded from this package. Because the rotor is 14.0 inch with an 18.0 inch minimum wheel diameter, check wheel clearance with the Q082P template before fitting the rear assembly. Brake hydraulic work should be handled by someone experienced with rear axle brake systems.
What’s included
The kit covers the 14.0 inch rear rotor with pre-assembled stainless hardware, the six-piston caliper, the backing plate with its park brake shoe assembly, and stainless braided hoses with hardware.
Not included: the front rotor, lug nuts and park brake cables.















