Overview
The Baer Brakes Extreme Plus rear disc kit in Comp Yellow, part number 4262094CY, is a rear brake system for Ford 8 inch and 9 inch small bearing axles on a 5×5.00 (5 lug) wheel pattern. It uses a 1-piece Monoblock 6-piston, 6S caliper that clamps a 14.0 inch, 2-piece slotted, drilled and zinc-plated rotor.
Baer mounts that caliper on a backing plate holding a modern 1-piece park brake shoe assembly. Stainless braided hoses and rotor hardware complete the set, and the park brake cables are not part of it.
Key features
- Monoblock 6-piston caliper, designated 6S, fixed type
- Caliper manufactured in Phoenix, Az
- Machined from US-sourced 2618 aluminum forging with a powder-coated finish
- Stainless pistons, abutments and noise suppression clips
- Staggered pistons help minimize uneven pad wear
- Dual seals against dust, weather and pressure
- 2-piece slotted, drilled, zinc-plated rotor with billet aluminum hat and pre-assembled NAS high grade stainless hardware
Planning the park brake
A park brake that shares the backing plate with the service caliper needs a plan for cables and adjustment. The shoes are the friction surface, so the adjuster should move smoothly and the cable should return the lever without binding. Routing matters, because a cable that bends sharply or rubs on a link will wear early and can hold the vehicle unevenly.
Many owners finish this type of rear system with a new cable set, new return springs and a fresh park brake adjuster. Look for worn shoes, glazed lining or a lever that travels too far before it grabs. Test the park brake on a slope with the transmission in the correct position before relying on it.
Brake fluid, pads and rotors are not the only parts that wear. Dust seals on the axle should be checked during the job, and any damaged boot should be replaced before the wheel goes back on. A clean, organized install makes later service far easier.
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 4262094CY |
| UPC | 90127947906 |
| Caliper color | Comp Yellow |
| Caliper | 1-piece Monoblock, 6-piston, 6S, fixed |
| Rotor outside diameter (rear) | 14.0 inch |
| Rotor thickness | 1.25 |
| Rotor type | 2-piece, vented, slotted, drilled, zinc plated |
| Rotor hat | Billet aluminum |
| Axle flange | Ford 8 Inch/9 Inch Small Bearing |
| Wheel bolt pattern | 5×5.00 (5 lug) |
| Minimum wheel diameter | 18.0 inch |
| Brake pad | FMSI D1247 |
| Park brake | Included, 1-piece shoe assembly in backing plate |
| Hoses | Stainless steel, braided |
| Template | N085P |
| Emission code | 6 |
| Grade | Performance |
| Country of origin | USA |
| Sold as | Kit |
Vehicle fitment
It is built for Ford 8 inch and 9 inch small bearing rear axle flanges with a 5×5.00 wheel bolt pattern, so match those dimensions to your rear axle. Make sure the year, model and trim of your vehicle are matched before ordering.
Wheel styles vary widely, so use the N085P template to check clearance against your wheel of choice. The minimum wheel diameter is 18.0 inch. Check your vehicle’s year, model and trim before you buy.
Installation notes
Rotors come with stainless hardware already assembled, and the stainless braided hoses are supplied. The park brake cables are not included, so they must come from a separate source. A qualified brake shop should verify caliper clearance and bleed the hydraulic lines after the kit is mounted.
What’s included
Comp Yellow 6S Monoblock caliper, 14.0 inch 2-piece rotors with billet aluminum hats, backing plate with park brake shoe assembly, and stainless braided hoses and hardware.
Not included: Park brake cables.
