Select your vehicle

Mr. Gasket Company Valve Cover Clamps – 9817

Mr. Gasket Company

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Mr. Gasket Company valve cover clamps, part number MRG9817
  • Universal fit, not tied to specific vehicles
  • Set of 8 clamps with 1/4x20x3/4 hex head bolts

Description

Overview

The Mr. Gasket Company MRG9817 is a set of valve cover clamps with 1/4x20x3/4 hex head bolts, supplied as a set of 8. Valve cover clamps hold a valve cover down on the engine, and this kit sits in the engine dress-up and valve cover range from Mr. Gasket Company.

It is a universal fit kit, so it is not built for one specific vehicle. Check the clamp and bolt sizing against your own valve cover before installing.

Key features

  • Set of 8 valve cover clamps
  • Includes 1/4x20x3/4 hex head bolts
  • It is a universal fit kit, not tied to one vehicle.
  • Part of the engine dress-up and valve cover category

Before you install

Valve cover clamps press the cover down evenly so the gasket seals against the cylinder head. Where a cover is held by bolts that run through its flange, clamps spread the load and help keep oil from weeping at the seam. Most of the work is checking fit and tension rather than anything about fluid compatibility.

Before fitting, clean the cover flange and head surface so the gasket seats flat. Look over the clamps for bends or cracks, and inspect the bolts for damaged threads. Tighten in a gradual, crisscross pattern using the torque values for your engine from a service manual, so the cover pulls down without warping.

Over time, clamps can loosen as gaskets compress and heat cycles the engine. Recheck the hold-down after the first few drives, and replace any bolt that shows stretching or corrosion. Clamps are often replaced along with the valve cover gasket whenever the cover comes off.

  • Clean the flange before fitting
  • Check each clamp for bends or cracks
  • Recheck tension after the first drives

Specifications

Brand Mr. Gasket Company
Part number MRG9817
Quantity 8 per set
Bolt size 1/4x20x3/4
Bolt head Hex head
Fitment Universal fit

Vehicle fitment

This is a universal fit part, so no particular year, make or model applies. Check the valve cover flange and bolt fit against your engine before installing.

Confirm your vehicle’s year, model and trim before ordering.

What’s included

The set includes 8 valve cover clamps and 1/4x20x3/4 hex head bolts.

Questions & Answers

Is the Mr. Gasket Company MRG9817 valve cover clamp kit vehicle-specific?

No. The MRG9817 is a universal fit kit, so it is not tied to a specific year, make or model. Measure your valve cover flange and confirm the 1/4x20x3/4 bolts suit your engine before ordering.

What is included with part number MRG9817?

The set includes 8 valve cover clamps and 1/4x20x3/4 hex head bolts. No other hardware or gaskets come with it.

What bolt size comes with the Mr. Gasket Company valve cover clamps?

The included fasteners are 1/4x20x3/4 hex head bolts. Compare thread and length with your current valve cover bolts before installing.

How can I tell if valve cover clamps need replacing?

Look for oil seepage at the cover edge, bent or cracked clamps, or bolts with damaged threads. Any of these signs means the hold-down should be inspected and the parts replaced if needed.

Should the valve cover gasket be replaced with the clamps?

Often yes. If the cover is off, a fresh gasket helps the seal hold, and the clamps can be reused when they are undamaged. Check fit against your engine before ordering.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon