Overview
The Baer Brakes 4262323FR is a rear SS4 Plus Deep Stage drag race brake kit for GM small pattern 10/12 bolt bearing-on-axle housing ends, the Buick, Olds and Pontiac rear axle flange. The kit pairs two S4 four-piston fixed calipers with 11 inch two-piece slotted, drilled rotors and is sized for wheels of 15 inch and larger.
The SS4 Plus Deep Stage system is a drag race system designed for heavy, fast cars that may also see street use. The kit is a single set of rear calipers with no park brake. The axle flange must measure 5.75 inch, so check your axle before choosing this kit. Confirm fit for your vehicle’s year, model and trim before ordering.
Key features
- Two-piece S4 four-piston calipers with 1.75 inch pistons, hard anodized aluminum pistons and stainless steel abutments
- Two-piece slotted, drilled, zinc-plated rotors on iron rotors with billet aluminum hats
- Billet aluminum hats drilled for 5/8 inch wheel studs
- Dust and weather seals are T compliant and suit the DR1 or HB100 pad type.
- Rotors pre-assembled with NAS high grade stainless hardware, with mounting hardware included
- Noise suppression clips and a powder coated Fire Red caliper finish
Before you buy a drag kit
Rear drag brakes take a lot of heat in a short run, so the calipers and rotors need to be matched to the axle before anything else. Start by confirming the housing type and flange size, then check that the rotor fits inside the wheel and that the caliper clears the wheel bolts. Mismatched parts are the most common reason these kits fail to fit on the first try.
Drag-use pads and rotors wear differently from street parts. Pads are usually replaced more often after hard stops, and rotors should be inspected for cracks, heat checks and uneven wear after every few runs. A worn pad can glaze, so check the pad surface for uneven contact before each event. Brake hoses should be checked for swelling and cracking whenever the system is opened up.
- Measure the axle flange before ordering
- Check wheel clearance around the caliper
- Replace pads and rotors together when either is worn
- Inspect hoses and fittings after each service
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 4262323FR |
| UPC | 844165049135 |
| Kit contents | 2 rear calipers, 2-piece rotors |
| Axle flange | GM small pattern 10/12 bolt bearing on axle (Buick/Olds/Pontiac) |
| Axle flange measurement | 5.75 inch |
| Bearing size | 3.150 inch |
| Caliper | S4, fixed, 4 pistons, Fire Red |
| Piston size | 1.75 inch |
| Rotor outside diameter | 11.0 inch |
| Rotor thickness | 1.02 |
| Rotor type | 2-piece, slotted, drilled, vented |
| Rotor material | Iron with aluminum hat, zinc-plated |
| Hat drilling | 5/8 inch wheel studs |
| Pad type | DR1 or HB100 (FMSI DR1) |
| Friction material | Semi-metallic |
| Minimum wheel diameter | 15.0 inch |
| Wheel bolt pattern | 5×4.50/5×4.75 |
| Lug count | 5 |
| Emission code | 6 |
| Template | S125A |
| Park brake | No |
| Country of origin | US |
Vehicle fitment
This kit is built around the GM small pattern 10/12 bolt bearing-on-axle flange used on Buick, Olds and Pontiac rear axles, and the axle flange must measure 5.75 inch.
Installation notes
The rotors come pre-assembled with stainless hardware, and mounting hardware is included. Brake hoses are not included, so plan for hose supply separately. Brake work on a drag car should be done by someone experienced with hydraulic brake systems.
What’s included
Two S4 rear calipers, two-piece rotors pre-assembled with NAS high grade stainless hardware, and mounting hardware.
Not included: brake hoses, front rotor, park brake, lug nuts.















