Overview
The Baer Brakes 4302252R is an Extreme Plus 14-inch rear brake kit in red, made for GM small pattern 10/12 bolt rear axles with C-clip housing ends and a 5×4.75 and 5×5 bolt circle. The red six-piston monoblock caliper, model 6S, grips a two-piece slotted, drilled rotor measuring 14.0 inch, and the kit uses the D1247 pad type.
The backing plate serves as the caliper mount and houses a one-piece park brake shoe assembly, so parking-brake duty stays inside the kit. The 14-inch Extreme Plus is intended for wheels 18 inches or larger, but wheel styles vary, so confirm clearance with the N110P template before installation.
Key features
- One-piece monoblock six-piston caliper, model 6S, finished in red
- Forging is US-sourced 2618 aluminum, CNC machined in the United States
- Floating caliper design
- Stainless steel pistons and abutments with noise suppression clips
- Staggered piston layout intended to reduce uneven pad wear
- Dual seals for dust, weather and pressure
- Slotted, drilled, zinc-plated two-piece rotor with a billet aluminum hat
- Powder coated finish
Heat and rear braking
Rear brake work on a shared axle affects more than stopping distance. The rear pads and rotors carry less load than the front, but a worn rear set can lock up under hard braking and upset stability on wet pavement. When the rotor is replaced, the pads, hardware and caliper slides should be inspected at the same time, since new metal sitting against worn friction material wears unevenly. Off-road, repeated descents heat the rear brakes more than most drivers expect, and the parking brake shoes can stick if the adjuster is neglected.
Before choosing a rear kit, measure the hub face and confirm the housing ends match the flange style in front of you. Stainless hoses are a sensible pairing with a monoblock caliper because they hold up to heat and flexing better than rubber. Check hose routing after installation so it cannot rub on the axle or suspension. Bleed the system fully, and retorque the caliper bracket bolts after the first few drives.
- Inspect rotor surfaces for scoring at each pad change
- Replace the park brake cable when lever travel grows
- Keep brake fluid fresh to reduce boiling under heavy use
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 4302252R |
| UPC | 844165043089 |
| Sold as | Kit |
| Axle | Rear |
| Axle flange | GM 10/12 bolt C-clip, small car pattern |
| Wheel bolt pattern | 5×4.75 / 5×5.00 |
| Lug count | 5 lug |
| Caliper | 6-piston monoblock, model 6S, floating |
| Caliper color | Red |
| Rotor outside diameter | 14.0 inch |
| Rotor thickness | 1.25 |
| Rotor type | 2-piece, vented |
| Rotor style | Slotted, drilled, zinc plated |
| Rotor material | Iron with aluminum hat |
| Brake pad FMSI number | D1247 |
| Minimum wheel diameter | 18.0 inch |
| Hose material | Stainless steel |
| Park brake | Included |
| Park brake cables | Not included |
| Front rotor included | No |
| Lug nuts included | No |
| Emission code | 6 |
| Template | N110P |
| Grade type | Performance |
| Country of origin | US |
Vehicle fitment
This red kit targets GM small pattern 10/12 bolt rear axles with C-clip housing ends. Bearing-on-axle housings use a separate flange and are not covered here. Confirm fit against your vehicle’s year, model and trim before ordering.
Rear axles with bearing-on-axle housing ends use a separate flange and are not covered by this kit. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Rotors come pre-assembled with stainless hardware, and stainless hoses with hardware are supplied. Cables for the park brake and lug nuts are excluded, so arrange them before the install date. Measure wheel clearance using the N110P template first. A qualified brake shop should fit the system and bleed the lines afterward.
What’s included
Six-piston monoblock caliper, backing plate with park brake shoe assembly, pre-assembled two-piece rotor, and stainless hoses with hardware.
Not included: front rotor, park brake cables and lug nuts.















