Select your vehicle

Omix-ADA Rear Floor Panel – 12008.04

Omix-Ada

$553.07Currently unavailable
Buy on Amazon

See similar parts on Amazon

Price and availability as of Nov 16, 2026 8:50 PM MST, from Amazon.com, and subject to change. The Amazon listing has the current details.

Check out with your Amazon account. Amazon handles delivery and returns.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Rear floor panel for 1955–1975 Jeep CJ5, CJ6 and Willys CJ-5 and CJ-6 models
  • Rear location and position, direct fit
  • Built to original specifications
  • Part number OAI12008.04 from Omix-Ada

Description

Overview

The Omix-Ada OAI12008.04 is a rear floor panel for Jeep CJ-series and Willys vehicles from 1955 to 1975. It is a direct fit for the rear location and is built to original specifications.

It suits restorers working on a CJ5, CJ6, Willys CJ-5 or Willys CJ-6. Coverage varies by model and year range, as shown below.

Key features

  • Rear floor panel for the rear location
  • Direct fit for the rear floor location.
  • Built to original specifications
  • Covered by a limited five year warranty.

Rust checks for floor panels

A rear floor panel supports passengers and cargo and carries the load of the seats and tie-down points. On older CJ-series vehicles it is often one of the first areas to corrode, because water collects under mats and in seams. Checking it before fitting a replacement helps show whether the surrounding metal is also worn.

Press firmly on the floor from above and below to find soft spots, and look at the seams, drain holes and mounting points for flaking metal. Clean away loose rust and check the frame rails beneath the floor, since they often corrode at the same time.

When a new panel is fitted, any cutting or welding should be planned with care, and bare metal should be treated with primer and sealant. Good preparation makes the replacement last longer.

  • Check seams and drain holes for rust
  • Inspect frame rails under the floor
  • Remove loose rust before fitting
  • Seal joints after welding or bolting

Specifications

Brand Omix-Ada
Part number OAI12008.04
Part type Rear floor panel
Location Rear
Position Rear
Fitment type Direct fit
Warranty Limited five year warranty
Vehicle years 1955–1975 Jeep CJ and Willys CJ models

Vehicle fitment

It fits these models:

  • 1959–1975 Jeep CJ5 (Base, Renegade)
  • 1959–1971 Jeep CJ6 (Base)
  • 1955–1958 Jeep Willys CJ-5
  • 1956–1958 Jeep Willys CJ-6

CJ7 models are not covered. The CJ5 and CJ6 entries apply only to the trims shown. Confirm your year, model and trim before ordering.

What’s included

The entry describes one rear floor panel only.

Fitment

VehicleYearsTrims
Jeep CJ51959–1975Base, Renegade
Jeep CJ61959–1971Base
Jeep Willys CJ-51955–1958All
Jeep Willys CJ-61956–1958All

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the OAI12008.04 rear floor panel fit a 1955 Willys CJ-5?

Yes. It fits 1955–1958 Jeep Willys CJ-5 models. It also fits 1959–1975 CJ5 Base and Renegade models and 1959–1971 CJ6 Base models.

Which CJ models are not covered?

CJ7 models are not covered. CJ5 coverage is limited to Base and Renegade trims, and CJ6 coverage is for Base only. Confirm your year, model and trim before ordering.

Is this part for the rear floor location?

Yes. The panel is designed for the rear floor location and is a direct fit. Compare part number OAI12008.04 with your original panel before installing it.

How do I tell if the rear floor needs replacing?

Push on the floor from above and below to check for soft spots, flaking rust or holes around the seams and mounting points. Replacement is usually needed when the metal is thin or crumbles. Check the frame rails beneath it too, since they often corrode alongside the floor.

Ready to order?

Order this part on Amazon and check out with your Amazon account. Amazon handles delivery and returns.

Buy on Amazon