Select your vehicle

Omix-ADA Accelerator Cable – 17716.02

Omix-Ada

Shop Jeep Wrangler YJ Accelerator Cable on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Omix-ADA accelerator cable, part number 17716.02, UPC 804314052522
  • For 2.5L four cylinder engine with carburetor
  • Fits 1987–1990 Jeep Wrangler (YJ) Base, Islander, Laredo, S, Sahara and Sport
  • Direct OE replacement design

Description

Overview

The Omix-ADA Accelerator Cable, part 17716.02, is a direct OE replacement accelerator cable for the 2.5L four cylinder engine with a carburetor. It fits 1987–1990 Jeep Wrangler (YJ) models.

The cable is built to original Jeep specifications and comes with a limited five year warranty from Omix-ADA.

Key features

  • Direct OE replacement design
  • For the 2.5L four cylinder engine with carburetor
  • Lists UPC 804314052522
  • Built to original specifications

Accelerator cable maintenance

On a carbureted Wrangler, the accelerator cable is the only link between the pedal and the carburetor linkage, so any stiffness is felt right away. Routing matters: the cable should bend gently around the firewall grommet and must not rub the exhaust, bracket or steering components. A cable with a clean, smooth path returns the throttle more reliably.

Slack is the adjustment that causes most problems. Too little slack can hold the carburetor partly open, while too much delays the response at the pedal. Set the cable so the throttle returns to idle with a small amount of free travel at the pedal, and recheck it after the first few drives on a new cable.

  • Route the cable away from heat and moving parts
  • Check the sheath for kinks at the firewall
  • Adjust slack at the carburetor end
  • Lubricate the pedal and bracket pivot points

Specifications

Brand Omix-ADA
Part number 17716.02
UPC 804314052522
Engine 2.5L four cylinder with carburetor
Fitment type Direct fit

Vehicle fitment

Manufacturer fitment lists 1987–1990 Jeep Wrangler (YJ) Base, Islander, Laredo, S, Sahara and Sport models.

Other years and Wrangler generations are not covered, so match your year and trim to the fit before ordering.

What’s included

Compare the parts you receive with your installation before starting.

SKU: OAI17716.02 Category:

Specification

Shipping weight 1.00 lbs
Package dimensions 30.00 × 1.00 × 1.00 in
brands

Fitment

VehicleYearsTrims
Jeep Wrangler (YJ)1987–1990Base, Islander, Laredo, S, Sahara, Sport

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the Omix-ADA accelerator cable 17716.02 fit a 1988 Wrangler YJ?

Yes. The manufacturer fitment covers 1987 to 1990 Jeep Wrangler (YJ) models, including Base, Islander, Laredo, S, Sahara and Sport trims. Check that your trim is in that list.

Is this cable for a carbureted engine?

Yes. It is made for the 2.5L four cylinder engine with a carburetor. Other engine types are not covered, so match your engine before choosing this cable.

What are the part number and UPC?

The part number is 17716.02 and the UPC is 804314052522. Use both numbers when comparing this cable with the original part.

What are the signs the accelerator cable is wearing out?

Hard pedal action, a throttle that sticks partly open or idle that drifts are common signs. Inspect the sheath, ends and clips for damage, and replace the cable when the pedal stays stiff after lubrication.

Can an accelerator cable be replaced without removing the carburetor?

Usually yes. The cable runs from the pedal to the carburetor end, so the carburetor can stay in place. Confirm the routing matches your original cable before disconnecting the old one.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Jeep Wrangler YJ Accelerator Cable on Amazon