Overview
The Jeep 34201535 is a wheel hub attaching bolt that holds the hub assembly to the steering knuckle on Dana 30 front axles. It fits Cherokee XJ, Comanche, Grand Cherokee ZJ and Wrangler YJ, TJ and LJ models.
This is the bolt that fastens the front hub assembly to the steering knuckle. Three bolts are required per assembly, so one front wheel end uses three and a full front axle uses six.
Jeep supplies the part under its own name as a direct fit replacement. No bolt length, thread size or torque value is published, so match the bolt to your old hardware and the factory service information.
This bolt is a small part, but the hub-to-knuckle joint carries the wheel loads, so using the correct fastener matters. Many owners renew the bolts whenever the front wheel ends are apart. Jeep does not publish the bolt length, thread pitch or material for the 34201535, so identification relies on the part number and the vehicle list. Omix-ADA’s 16560.61 is noted as replacing this same OE number, which can help when comparing aftermarket and factory hardware.
Key features
- Attaches the hub assembly to the steering knuckle
- Intended for Dana 30 front axles
- Three bolts are needed for each hub assembly
- Jeep-branded direct fit part
- Covers six Jeep model lines
Hub bolt service tips
A hub attaching bolt carries load between the hub and the knuckle every time the wheel turns, so it deserves the same care as larger fasteners. When the front hub is apart, inspect the threads on the knuckle and the bolt holes for damage. A cross-threaded or stretched bolt can lead to a loose hub, which shows up as clunking or wobble at speed.
Plan the job so every bolt is ready before the hub goes back on. Clean the mating faces, and do not reuse a bolt that shows thread damage or corrosion. Pair the bolt work with a bearing and seal check, since the hub assembly is often opened at the same time. Use a torque wrench set to the factory figure for your Jeep.
- Inspect threads on the knuckle and bolts
- Clean mating faces before reassembly
- Replace any bolt that is stretched or corroded
- Check bearings and seals while the hub is apart
Specifications
| Brand | Jeep |
|---|---|
| Part number | 34201535 |
| UPC | 70000363586 |
| Part type | Wheel hub attaching bolt |
| Axle | Dana 30 |
| Bolts per hub assembly | 3 |
Vehicle fitment
It fits these vehicles and trims:
- 1984–2001 Jeep Cherokee (XJ) (Base, Briarwood, Chief, Classic, Country, Laredo, Limited, Pioneer, SE, Sport)
- 1986–1992 Jeep Comanche (Base, Chief, Custom, Eliminator, Laredo, Pioneer, X, XLS)
- 1993–1998 Jeep Grand Cherokee (ZJ) (5.9 Limited, Base, Laredo, Limited, Orvis, SE, TSi)
- 2004–2006 Jeep Wrangler (LJ) (Unlimited, Unlimited Rubicon)
- 1997–2006 Jeep Wrangler (TJ) (65th Anniversary Edition, Rubicon, SE, Sahara, Sport, X)
- 1987–1995 Jeep Wrangler (YJ) (Base, Islander, Laredo, Renegade, Rio Grande, S, SE, Sahara, Sport)
The list runs only through the Cherokee XJ, Comanche, Grand Cherokee ZJ and the three Wrangler generations named above. It leaves out the Wrangler JK, the Grand Cherokee WJ and the CJ models. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Because each hub assembly takes three of these bolts, count the full number you need for the wheel ends you are servicing before you start. Torque to the factory figure for your Jeep, since none is published here.
What’s included
One hub attaching bolt, part number 34201535.
Not included: the other two bolts each hub assembly needs, plus bearings and seals.









