Select your vehicle

Crown Automotive SR4 Manual Trans Input Bearing Retainer Gasket – J8127392

Crown Automotive

$9.26Usually ships within 6 to 7 days
Buy on Amazon

See similar parts on Amazon

Price and availability as of Nov 19, 2026 1:00 AM MST, from Amazon.com, and subject to change. The Amazon listing has the current details.

Check out with your Amazon account. Amazon handles delivery and returns.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Crown Automotive gasket for the SR4 manual transmission input bearing retainer
  • Position: front, part number J8127392
  • Fitment covers 1980–1983 Jeep CJ5 and CJ7
  • Also covers 1981–1983 Jeep Scrambler

Description

Overview

The Crown Automotive J8127392 is a front SR4 manual transmission input bearing retainer gasket. Fitment covers 1980–1983 Jeep CJ5 and CJ7 and 1981–1983 Jeep Scrambler models.

The position is given as front, and only the gasket is described. No retainer, bolts or other hardware are named.

Key features

  • Gasket for the SR4 manual transmission input bearing retainer
  • Fits the front position of the SR4 input bearing retainer.
  • Part number J8127392
  • Covers CJ5, CJ7 and Scrambler, 1980–1983

Sealing the input bearing retainer

The input bearing retainer gasket seals the joint between the retainer and the front of the transmission case. Its job is to keep gear oil in and dirt out, and it does that only when the mating surfaces are clean, flat and undamaged. Old gasket material left on either face is one of the most common causes of a seep that appears after a fresh rebuild.

A gasket is only as good as the surfaces it sits on. Scrape off old material gently so the case is not scored, then wipe both faces with a clean solvent. Many installers use a light film of gasket sealant only where the procedure calls for it, since excess sealant can squeeze into the input bearing and block oil flow.

  • Clean both mating surfaces before fitting
  • Avoid scoring the aluminum case face
  • Use sealant only where the procedure calls for it
  • Check the retainer bolts for thread damage

Specifications

Brand Crown Automotive
Part number J8127392
Transmission SR4 manual
Position Front

Vehicle fitment

Fitment covers 1980–1983 Jeep CJ5 (Base, Golden Eagle, Laredo, Limited, Renegade), 1980–1983 Jeep CJ7 (Base, Golden Hawk, Laredo, Limited, Renegade) and 1981–1983 Jeep Scrambler (Base, SL, SR).

Model years after 1983 are not covered for any of these vehicles. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Fitting this gasket means removing the input bearing retainer, which opens the front of the transmission. Clean both mating surfaces before setting the new gasket.

What’s included

One retainer gasket. No bolts, retainer or other parts are named.

Fitment

VehicleYearsTrims
Jeep CJ51980–1983Base, Golden Eagle, Laredo, Limited, Renegade
Jeep CJ71980–1983Base, Golden Hawk, Laredo, Limited, Renegade
Jeep Scrambler1981–1983Base, SL, SR

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does J8127392 fit the SR4 manual transmission?

The gasket is made for the SR4 manual transmission input bearing retainer. Fitment covers 1980–1983 Jeep CJ5 and CJ7 and 1981–1983 Scrambler models. Confirm your vehicle's year, model and trim before ordering.

Is this the front or rear gasket?

Front. The position is given as front, so this gasket belongs to the front input bearing retainer rather than a rear location.

Does the gasket come with a retainer or bolts?

No hardware is named. The gasket is described alone, with no retainer, bolts or other parts, so check your parts before starting the job.

What signs point to a leaking input bearing retainer gasket?

Oil seeping along the front of the transmission, especially near the bell housing joint, is the usual sign. Wetness that grows after a fluid change or a long drive suggests the gasket has lost its seal.

Should the input bearing be checked when the gasket is replaced?

It is a good time to check. The retainer has to come off to replace the gasket, so look over the input bearing for rough spots or heat marks before reassembly.

Ready to order?

Order this part on Amazon and check out with your Amazon account. Amazon handles delivery and returns.

Buy on Amazon