Select your vehicle

Baja Designs OnX6 30″ Full Laser Dual Control Light Bar – 413007

Baja Designs

Shop Baja Designs Light Bars on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • 30 inch OnX6 Full Laser light bar with a 1.5 degree pattern
  • 9000 lumens and 270 watts with a 19.5 amp draw
  • IP69K waterproof, submersible to 9ft, pressure washable
  • Built-in overvoltage protection and IK10 impact rating

Description

Overview

The Baja Designs OnX6 30 Inch Full Laser Dual Control Light Bar, part 413007, is a single row, straight 30 inch light bar from the Laser Light series. It is rated at 9000 lumens and 270 watts, with a 19.5 amp draw. The bar uses laser technology with a 1.5 degree pattern for long-range distance light.

Its laser light is designed to throw light 350 percent farther than the OnX6+ light bar. The 1.5 degree pattern reaches distances that LED or HID platforms cannot match. The bar uses an aircraft grade aluminum housing with a mil-spec hard anodize finish and a billet machined aluminum bezel.

Key features

  • Laser light pattern at 1.5 degrees
  • 9000 lumens
  • 270 watts
  • Throws light 350 percent farther than the OnX6+ light bar.
  • Aircraft grade aluminum with mil-spec hard anodize
  • Billet machined aluminum bezel and hard coated polycarbonate lens
  • IP69K waterproof, submersible to 9ft, pressure washable
  • Built-in overvoltage protection

Wiring and fuse planning

A bar with a 19.5 amp draw needs a fused feed sized to its load, and a relay close to the battery keeps the high current off the switch circuit. Plan the switch location before mounting so the wire route stays short, protected and clear of heat sources.

Ground connections matter as much as the feed. Clean the chassis contact point to bare metal, tighten it firmly, and check it again after the first rough trips. Seal connectors with dielectric grease and secure the cable so it cannot rub against edges or moving parts.

  • Use a relay and fuse close to the battery
  • Route wiring away from heat and moving parts
  • Seal connectors with dielectric grease
  • Clean and tighten the ground point

Specifications

Brand Baja Designs
Part number 413007
Series OnX6+ Laser Light
Length 30 inch
LED row configuration Single row, straight
Beam pattern Laser, 1.5 degree
Output 9000 lumens
Power 270 watts; 19.5 amp draw
LED life 49930 hours
Housing Aircraft grade aluminum, mil-spec hard anodize
Bezel Billet machined aluminum
Lens Hard coated polycarbonate
Ratings IP69K; IK10 compliant; exceeds MIL-STD810G
Hardware and bracket Stainless steel

Vehicle fitment

It is designed as a universal fit, so the bracket and mounting location decide where it can go. Check the clearance and the wire route before drilling.

Installation notes

The 19.5 amp draw calls for a fused feed sized to the bar’s load. Check the bracket and wiring before use, and check local rules for auxiliary lighting on public roads, since high-output distance lights can be restricted. The bar ships with stainless steel hardware and a stainless bracket, so no separate hardware is listed.

What’s included

One 30 inch OnX6 Full Laser light bar with its stainless steel hardware and bracket.

Questions & Answers

Is the OnX6 Full Laser bar a universal light bar?

Yes. It is a universal fit light bar, so it is not built for one model. The bracket and mounting location decide the fit, so check clearance on your vehicle before mounting.

How far does the laser light reach?

The laser light is designed to throw light 350 percent farther than the OnX6+ light bar, using a 1.5 degree pattern. That pattern concentrates the output into a long, narrow beam for distance.

Is the bar waterproof?

Baja Designs rates it IP69K, waterproof up to 9ft and pressure washable, with a hard coated polycarbonate lens. The aircraft grade aluminum housing and billet machined bezel add to its build.

Does the bar need a separate switch?

Most setups use a separate switch or control module, so the bar can be run without the ignition on. Pick the switch location before mounting so the wire route stays short and protected.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Baja Designs Light Bars on Amazon