Overview
The California Super Trucks CSP-C28-7 is a high angle CV style front driveshaft for 2017 and 2018 Chevrolet Silverado 2500HD and 3500 and GMC Sierra 2500HD and 3500 trucks equipped with the CST 8-10 inch suspension lift and the Duramax and Allison combination. It is designed to reduce or eliminate front driveline vibrations and noise when the truck is run in 4WD.
A lift changes the angle of the front driveshaft, and at steeper angles a standard shaft can bind and cause vibration. This shaft uses a dual universal joint cage, also called a dual cardan, at the transfer case end. That arrangement effectively doubles the angle the driveshaft can run through without binding. The shaft is also longer, and it works with CST 8-10 inch lifts only.
Key features
- High angle CV style front driveshaft
- Dual universal joint cage (dual cardan) at the transfer case side
- Dual cardan arrangement effectively doubles the angular capacity of the driveshaft
- Longer shaft length designed for CST 8-10 inch suspension lifts
- Designed to reduce or eliminate driveline vibrations or noise in 4WD
- Designed for the Duramax diesel and Allison transmission combination
Driveline angle and vibration
A driveshaft works through the angles set by the transfer case, the front axle and the suspension. When a lift raises the truck, those angles change, and the joints can work harder than they were built to handle. Vibration in 4WD, a humming that rises with speed, or a shudder under acceleration are common signs that the driveline is running at an angle it does not suit.
Shaft length matters as much as joint design. A longer shaft has to match the new ride height and the transfer case position, so a shaft sized for a different setup can bind or pull on the joints. Keep the transfer case output and the axle pinion aligned during installation, and check for worn joints, cracked boots or loose fasteners at each service.
- Check the front pinion angle after lift work
- Inspect the joints for play or rust
- Re-torque driveshaft fasteners after the first drives
- Keep the shift linkage free of binding
Specifications
| Brand | California Super Trucks |
|---|---|
| Part number | CSP-C28-7 |
| UPC | 700008267111 |
| Position | Front |
| Type | High angle CV style driveshaft |
| Joint design | Dual universal joint cage (dual cardan) at the transfer case side |
| Required lift | CST 8-10 inch suspension lift |
| Engine and transmission | Diesel engine with Allison transmissions |
| Required accessory | Low profile shift linkage bracket CSS-C22-13, purchased separately |
Vehicle fitment
The fit covers 2017–2018 Chevrolet Silverado 2500 HD and 3500 HD trucks with High Country, LT, LTZ and WT trims, and 2017–2018 GMC Sierra 2500 HD and 3500 HD trucks with Base, Denali, SLE and SLT trims. It is designed for these trucks running the CST 8-10 inch lift.
Trucks outside the 2017–2018 model years, and 1500 series Silverado and Sierra models, are not covered. It is intended only for trucks with a CST 8-10 inch lift. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Install the CST 8-10 inch suspension lift first, since this driveshaft is designed to work only with that lift. The low profile shift linkage bracket CSS-C22-13 is required and must be purchased separately, so have it on hand before the driveshaft swap. After installation, check the driveline angles and confirm the shaft runs smoothly in 4WD.
A driveshaft is heavy and fastened under the truck, so support the vehicle securely on stands and keep hands clear while the shaft is removed.
What’s included
The package is the front driveshaft with its dual universal joint cage. The CST 8-10 inch suspension lift and the low profile shift linkage bracket CSS-C22-13 are required and must be purchased separately.



